EasySplicer PRO Welder
* Fusion splicing made easy and affordable with the EasySplicer PRO * X/Y, 4 motors, core positioning * Dual X/Y cameras * Works with separate fiber holders compatible with all types of optical fiber cables * For single-mode and multimode fibers * Splicing time of 6 seconds and oven time around 25 seconds * Loss estimation and splice tension test performed * Long-lasting electrodes (4k splices) and high-altitude splicing (5000m) * Easy to use and transport Perfect for FTTH installers EasySplicer PRO is a 4-motor fusion splicer, with central X/Y positioning, designed for daily operation in optical fiber networks. It is small and convenient, easy to carry for any type of work. The entire system can be used in its carrying case to prevent dirt and dust from reaching the sensitive parts of the fusion splicer. The design is very robust, and even though splicing should take place in good conditions (indoors), the EasySplicer PRO is also intended to be used in the field. The EasySplicer Pro is unique in that it uses fiber holders for different market cables. The holders make it very easy to prepare and load the fiber into the splicer. A big advantage is that you can mix fibers and get a very nice appearance (and work) on cable splices. The precision is extremely high => The splice has a maximum loss of 0.02 dB (single mode) controlled after splicing. Pre-splice information is also provided and displayed on the screen (such as Bad fiber, Dirty fiber, and Too much offset). EasySplicer PRO constantly calibrates for changes in the environment (such as humidity, atmospheric pressure, and temperature). This can also be done manually, for example, at the beginning of the workday. EasySplicer PRO comes with a ceramic/teflon oven that is also ready for Splice on Connectors (SOC). The battery inside the device is small but very powerful. Approximately 200 splicing cycles (with oven) can be performed before needing to recharge.
Included parts:
* Oven (built-in).
* 3 pairs of fiber holders, 250um 900um, and loose tube.
* Cleaver with trash can.
* Stripper.
* Rechargeable battery (built-in).
* Power supply block 13.5V.
* Carrying case.
* Car charger.
* Powerbank charger.
* SOC holders.
|
Caractéristiques techniques
Splicing method: Core positioning (X/Y).
Fiber types: SMF fiber, 50/125um MMF and 62.5/125um, Primary coated fiber 250um and secondary 900um.
Fiber handling: Fiber holders, 3 pairs (250, 900, and loose tube).
Optional for any cable type (branching cable, 2mm, 3mm, Splicing on connectors, etc.).
Calibration: Automatic (temperature and air pressure) or manual.
Splicing programs: 40 groups.
Operation modes: Automatic or Manual.
Typical splice loss: 0.02dB SMF 0.01dB MMF.
Return loss: >60dB.
Tension test: Yes, 1.8-2.2 Newton.
Typical cycle time: Splicing 6 sec, oven heating time 25 sec.
Sleeve dimensions: Maximum length of 64mm.
Display: LCD, color, 4.3".
Oven: Ceramic/Teflon type. 40/60mm sleeves in approximately 25 sec.
Electrodes: lifespan >4000 splices.
Magnification cameras: x 250 (X or Y) x 125 (X and Y together).
Connection: USB 2.0 for information download and upgrades.
Splice memory: 4000 results internally.
Altitude compensation: Automatic up to 4000 meters altitude.
Operating environment: with humidity and temperature compensation: -10C +50°C, max 95% RH, non-condensing.
Size: 149 x 120 x 127mm.
Weight: 1.9 Kg.
Power sources: External power supply 13.5V, 100-240VAC (50-60Hz). Built-in 5800mAh Lion battery.
Splicing capacity: 200 splices with oven cycles.
Additional features: Loss estimation, fiber defect detection, SD card for logging, etc.
|